|
| |
|
TI-HP1 High Performance
Ultrasonic Thickness Gauge
Note: This Gauge has been
discontinued and replaced by the TI-MVX Gauge |
|
The
CHECK-LINE TI-HP1 Ultrasonic Thickness Gauge accurately measures the
most difficult materials, such as rubber - from only one side!
The
TI-HP1 is a full-function, A-Scan thickness gauge with a wide variety of
modes and features for extra versatility. The A-Scan display options and
dual gates enable the TI-HP1 to be optimized for multi-mode through paint
requirements.
The
TI-HP1 is shipped with software for transferring data to and from a PC.
Software is compatible with Windows 95/98/NT. |
 |
|
For more detailed thickness analysis,
an A-Scan mode can be used. |
Gauge configuration and calibration is done via plain English menus. |
|
 |
Complete Kit includes: gauge, leather pouch with hand strap, shoulder
straps, combined sensor, sensor lead, spare AA batteries, test block,
operating instructions, calibration certificate, couplant. |
Ordering Information:
|
Buy Now |
Part # |
Description |
Price |
|
|
ELE-TI-HP1 |
High Performance Thickness Gauge |
$2,240.00 |
|
|
ELE-T-102-2700 |
Thru Paint with Metal Wall >1" |
$310.00 |
|
|
ELE-T-104-0600 |
Fiberglass and other Porous Materials |
$325.00 |
|
|
ELE-T-104-1000 |
Thick Plastics |
$275.00 |
Specifications:
|
Measuring |
|
Range: |
Measures from 0.010 to 480 inches (0.63 to 12 Meters) in steel.
Switch to select english or metric units. |
|
Resolution: |
Standard Mode - .001 inches (0.01 mm)
High Resolution Mode - .0001 inches (0.001 mm) |
|
Velocity Range: |
.0500 to .3937 in/ms (1270 to 10,000 meters/sec)
Selectable pulse repetition rate allows for high speed scanning or low power
operation.
Single and Two point calibration capability. |
|
Ultrasonic Specifications |
|
Measurement Modes: |
Pulse-Echo (flaws, pits) Echo-Echo (thru paint, precision delay line) |
|
Pulser: |
Tone-burst (push-pull). Selectable 1, 2 or 4 pulses. Selectable
frequencies (MHz): 0.5, 1, 2.25, 5, Hi Freq. |
|
Receiver: |
Low noise pre-amplifier.
Adjustable gain control. |
|
Timing: |
160 MHz 10 ppm TCXO controlled digitizer. |
|
Memory: |
8 megabit non-volatile ram. |
|
Power Source |
Four
1.5V alkaline or 1.2V NiCad C cells 100-240 VAC input 12VDC power supply
Typically operates for 30 hours on alkaline and 15 hours on NiCad
|
|
Physical |
|
Size: |
8.5 in (W) x 6.5 in. (H) x 2.0 in (D) 216 mm x 165 x 51 mm |
|
Weight: |
2lbs. 10 ounces (1.2 Kg) |
|
Keyboard: |
Membrane pad with tactile keys. |
|
Operating Temperature: |
-4° to 122° F(-20° to 50° C) |
|
Case: |
Extruded aluminum body with nickel-plated aluminum end caps (gasket
sealed). |
|
Data Output: |
RS232 port out Windows interface software. |
|
Display: |
Backlit LCD-3.5"W x 2.0"H |
|
Display |
|
Display Views: |
Rectified (flaw view)
RF (full waveform view)
Digital thickness readout
Multi-function 6 digit graphic LCD, backlit for use in poor light
conditions.
Measurements displayed in inches, inches/microsecond.
Bar
graph indicates stability of reading.
Data
Logger (internal):
1000
pages of memory (alpha numeric storage)-I main cell reading, 1 waveform, 2
comment lines, and 16 sub readings per page. OBSTRUCT for indicating
inaccessible locations.
|
|
Transducer |
|
Transducer Types Dual Element (1 to 10 MHZ)
Single Element Contact (500 KHz to 10 MHz)
Single Element Delay Line (5 to 22 MHz)
Locking quick disconnect "00" LEMO connectors.
Standard 4 foot cable.
Custom transducers and length cables available for special applications |
|
